Производство PolusAutomatica, Россия.
Полный аналог Интерфейсной платы для QAA 73 KHG71407251 BAXI (произведено Siemens).
Для присоединения к котлам:
BAXI NUVOLA-3 B40,
BAXI NUVOLA-3 Comfort,
BAXI SLIM
! НЕ подходит для SLIM HPS, SLIM EF !
- подключение контроллеров управления отоплением, термостатов ZONT, MY HEAT по протоколу OpenTherm,
- подключение комнатного термостата QAA 73,
- подключения устройств диагностики и программирования по протоколу OpenTherm.
Функции:
- программирование режимов отопления и ГВС;
- самодиагностика;
- включение-выключение котла, установка температур контуров отопления и ГВС.
Для удаленного управления температурой бойлера подключите к котлу датчик температуры бойлера KHG 714061911.
ниже приведены коды ошибок BAXI SLIM (подключение ПО цифровой шине) из оригинальной инструкции:
E-0 No Error Detected
E-10 Outside Air Sensor Fault / Not Detected
E-20 Flow Water Sensor Fault / Not Detected
E-28 Flue Gas Sensor Fault / Not Detected
E-40 Return Water Sensor Fault / Not Detected
E-50 HWS Sensor Short Circuit 1
E-52 HWS Sensor Short Circuit 2 (Not Used)
E-60 Faulty Room Sensor
E-61 Faulty Room Sensor
E-62 Incorrect Room Unit Connected
E-77 Air Pressure Sensor Not Detected (Not Used)
E-78 Water Pressure Sensor Defective (Not Used)
E-81 LPB Short Circuit (Boiler Cascade Wiring)
E-82 LPB Address Conflict (Boiler Cascade Settings)
E-91 EEPROM
E-92 Hardware Malfunction
E-100 Conflict Between Time of Day Master Control (Boiler / QAA73 / RVA47)
E-110 Boiler Water Temperature Overheat
E-111 Boiler Temperature Too High (Auto Resetting)
E-113 Flue Gas Temperature overheat
E-117 High System Water Pressure Sensor (Not Used)
E-118 Low System Water Pressure Sensor (Not Used)
E-119 System water Pressure Switch Activated
E-124 Boiler Temperature Too High (Auto Resetting)
E-128 No Flame Detected After Ignition Attempts (Version D LMU)
E-129 Flame Extinguished During Operation (Version D LMU)
E-130 Flue Temperature Too High (Auto Resetting)
E-131 Fault With Burner
E-132 External Safety Interlock Activated (Open Circuit) X10-03
E-133 No Flame Detected After Ignition Attempts
E-134 Flame Extinguished During Operation
E-135 Air Supply Error (Not Used)
E-140 LPB Segment / Address Not Recognized (Boiler Cascade Settings)
E-142 LPB Missing Partner (Boiler Cascade Settings)
E-148 LPB Interface Not Configured (Boiler Cascade Settings)
E-150 General Boiler Fault
E-151 Boiler LMU64 Controller Malfunction
E-152 Boiler LMU64 Controller Parameter Programming Error
E-153 Boiler Reset Button Pressed When Boiler Was Not In Fault. Boiler Control Interlocked
E-154 Operational Error Detected Relevant to a Parameter setting. Commonly a System Hydraulic Error
E-160 Fan Not Reaching Set Point
E-161 Combustion Fan Speed Too High
E-162 Air Pressure Switch Fault (Not Used)
E-164 Flow Switch / Pressure Switch Open
E-166 Air Pressure Switch Fault (Not Used)
E-180 Boiler Operating in Chimney Mode 50% Output
E-181 Boiler Operating in Commissioning Mode
E-183 Boiler Controller / QAA73 Room Unit in Parameter Setting Mode
-bu- Controller / display card malfunction (Ribbon cable loose / wiring error)
