Интерфейсная плата для QAA 73 KHG71407251- PolusAutomatica

Производство PolusAutomatica, Россия.

Полный аналог Интерфейсной платы для QAA 73 KHG71407251 BAXI (произведено Siemens).

Для присоединения к котлам:

BAXI NUVOLA-3 B40,

BAXI NUVOLA-3 Comfort,

BAXI SLIM

! НЕ подходит для SLIM HPS, SLIM EF !

- подключение контроллеров управления отоплением, термостатов ZONT, MY HEAT по протоколу OpenTherm,

- подключение комнатного термостата QAA 73,

- подключения устройств диагностики и программирования по протоколу OpenTherm.

Функции:

- программирование режимов отопления и ГВС;

- самодиагностика;

- включение-выключение котла, установка температур контуров отопления и ГВС.

Для удаленного управления температурой бойлера подключите к котлу датчик температуры бойлера KHG 714061911.

ниже приведены коды ошибок BAXI SLIM (подключение ПО цифровой шине) из оригинальной инструкции:

E-0 No Error Detected

E-10 Outside Air Sensor Fault / Not Detected

E-20 Flow Water Sensor Fault / Not Detected

E-28 Flue Gas Sensor Fault / Not Detected

E-40 Return Water Sensor Fault / Not Detected

E-50 HWS Sensor Short Circuit 1

E-52 HWS Sensor Short Circuit 2 (Not Used)

E-60 Faulty Room Sensor

E-61 Faulty Room Sensor

E-62 Incorrect Room Unit Connected

E-77 Air Pressure Sensor Not Detected (Not Used)

E-78 Water Pressure Sensor Defective (Not Used)

E-81 LPB Short Circuit (Boiler Cascade Wiring)

E-82 LPB Address Conflict (Boiler Cascade Settings)

E-91 EEPROM

E-92 Hardware Malfunction

E-100 Conflict Between Time of Day Master Control (Boiler / QAA73 / RVA47)

E-110 Boiler Water Temperature Overheat

E-111 Boiler Temperature Too High (Auto Resetting)

E-113 Flue Gas Temperature overheat

E-117 High System Water Pressure Sensor (Not Used)

E-118 Low System Water Pressure Sensor (Not Used)

E-119 System water Pressure Switch Activated

E-124 Boiler Temperature Too High (Auto Resetting)

E-128 No Flame Detected After Ignition Attempts (Version D LMU)

E-129 Flame Extinguished During Operation (Version D LMU)

E-130 Flue Temperature Too High (Auto Resetting)

E-131 Fault With Burner

E-132 External Safety Interlock Activated (Open Circuit) X10-03

E-133 No Flame Detected After Ignition Attempts

E-134 Flame Extinguished During Operation

E-135 Air Supply Error (Not Used)

E-140 LPB Segment / Address Not Recognized (Boiler Cascade Settings)

E-142 LPB Missing Partner (Boiler Cascade Settings)

E-148 LPB Interface Not Configured (Boiler Cascade Settings)

E-150 General Boiler Fault

E-151 Boiler LMU64 Controller Malfunction

E-152 Boiler LMU64 Controller Parameter Programming Error

E-153 Boiler Reset Button Pressed When Boiler Was Not In Fault. Boiler Control Interlocked

E-154 Operational Error Detected Relevant to a Parameter setting. Commonly a System Hydraulic Error

E-160 Fan Not Reaching Set Point

E-161 Combustion Fan Speed Too High

E-162 Air Pressure Switch Fault (Not Used)

E-164 Flow Switch / Pressure Switch Open

E-166 Air Pressure Switch Fault (Not Used)

E-180 Boiler Operating in Chimney Mode 50% Output

E-181 Boiler Operating in Commissioning Mode

E-183 Boiler Controller / QAA73 Room Unit in Parameter Setting Mode

-bu- Controller / display card malfunction (Ribbon cable loose / wiring error)